Make Your Own Hats | Page 8

the same as used in covering the rolled brim.
SHEER MATERIALS--
In covering with anything as sheer as georgette, it is advisable to line with some other material first. The color could be made deeper by using a lining of the same color, or made paler by lining with white. The lining should be fitted and sewed on with the outside material.
PATTERN FOR HAT WITH ROLLED OR CLOSE-FITTING BRIM--
The pattern for any hat is first cut from a flat piece of paper. The headsize is marked as for flat sailor and the headsize wire pinned on. The pattern is then slashed in to headsize wire from the outside edge, the slashes lapped over and pinned. If the hat is to be rolled more closely on one side than on the other, the greater number of slashes must be placed there. In this way the pattern can be adjusted to any desired shape. It is an advantage sometimes to cut the paper pattern through in the back, leaving pins in the slashes, and lay out flat on another piece of paper for a new pattern. This eliminates some of the slashes and makes further experiments easier. Pattern-making is very important, and it is of extreme value to make as many patterns as possible before cutting the foundation fabric. Changing a pattern the slightest sometimes makes a great deal of difference in its becomingness. Of course a brim may be changed by adding a slash or two in the buckram, or by inserting a V shape to give more flare, but the fewer seams the better for the hat frame. A rolled or close-fitting brim is more difficult to cover than a sailor or mushroom shape.
TO COVER A CLOSE-FITTING OR ROLLED BRIM--
Place corner of material on top of brim at front and pin on the edge. Always use the same method of pinning on the edge as given in the first lesson. Draw the material down to the headsize wire and pin. Work the material out smoothly toward the left and pin at the edge; also at the headsize wire. Then proceed in the same way toward the right, always pinning closely. Be sure to keep the material tight and smooth both at edge and at the headsize wire. Allow the fullness to go where it will. The seam should be located at the center back. Cut away all superfluous material, allowing three-eighths of an inch seam at the center back. Turn the raw edges under away from each other at the seam and slipstitch together neatly.
TO SLIPSTITCH SEAM--
Bring needle through edge of fold on one side and enter the needle through edge of fold on other side exactly opposite. Slip needle along in this fold one-eighth of an inch, then bring the needle through to the edge of the fold and take a stitch one-eighth of an inch long in the fold of the other side, always being careful to begin the stitch exactly opposite the end of the one preceding. Try to cut the material out from inside the headsize wire in one piece so that it may be used for something else. Examine the material carefully to make sure that it fits perfectly. Baste with a stab stitch close to the headsize wire on the outside; remove all pins as soon as possible. After basting this, you will sometimes find that the material needs a little more adjusting at the edge. Turn the velvet over the edge one-fourth inch and sew down with an overcasting stitch.
TO GLUE VELVET TO THE BRIM--
When there is a decided roll to a brim, it is sometimes most difficult to keep the velvet smooth and to make it lie close to the brim, so we resort to milliner's glue. Do not use glue on satin, or on any fabric thinner than velvet, or on any frame other than buckram. Care should always be taken to have the smooth side of the buckram on top when the velvet is to be glued on.
After fitting the velvet carefully and sewing the seam in the back, remove the pins from the outer edge and gather the velvet up inside the headsize where it is to be held while the glue is being spread on the buckram. The glue must be spread very evenly. It will make a neater job to glue the seam of the velvet open before going further. Be very careful to keep the glue away from the right side of the velvet. Next, rub the glue on the frame with a stiff brush until it is smooth, then spread the velvet back into place, pressing and smoothing it with the hands from the headsize wire out. Watch it carefully for any places which have not sufficient glue, as the material may be raised before it is