Make Your Own Hats | Page 7

every three inches through edge of fold at right angles to edge and close to edge. This is to mark the line that must be placed on the edge of the brim. If the velvet is not placed evenly, there will be found a greater amount of fullness on one side than on the other. Place velvet over the brim and pin on edge at points marked by pins. Stretch as tight as possible. On a brim of this width all of the fullness should be worked out. If this is found to be very difficult, lay the brim aside, with the velvet pinned on, for an hour or for overnight, and the velvet will be found to give a little more. Remove as much of the length as possible. Locate seam, remove from frame, sew seam, and replace as before. Sew on top close to headsize wire, working out all the fullness possible; pull under part up into headsize. Sew one-fourth inch above headsize wire onto the flaps, being careful not to pull the thread too tight or the headsize wire will be reduced in size.
FACINGS--
A pleasing variety is sometimes obtained by using a colored underfacing on a black hat. The entire facing may be of a contrasting color or extend only from headsize wire to within an inch of the edge of the brim. In this case there could be a strip of material the same as upper facing an inch and a half wide finished at the edge of the brim with a wire. Then the colored facing would be finished over the edge of this with another wire.
BRIMS COVERED WITH TWO KINDS OF FABRIC--
A flat brim or mushroom shape is often covered by using two fabrics, which may be of the same color or of contrasting colors. Small pieces of old material may often be conserved in this manner and the hat at the same time have much charm. For instance, the edge of the hat could have a bias band of satin, two or more inches wide, stretched around the edge of the brim, with the rest of the brim covered with velvet overlapping the satin and finished with a wire both on top and bottom, or only on one side. Underside of brim may be finished the same way, or the facing may be brought out even with the edge and finished with a wire.
SHAPED BRIM FOUNDATION--
The simplest shaped brim is the mushroom style.
TO MAKE PATTERN FOR BRIM--
Make a paper pattern the same as for the straight brim sailor. Measure the same for the headsize wire, join ends of wire, shape to fit the head, and pin on paper pattern of any desired width. To make the brim droop, slash the pattern from the edge to the headsize wire in four different places equally distant. Lap these slashes one-fourth inch at the edge, and pin. The pattern may also be slashed in eight or more different places if desired, the slashes being adjusted by lapping more or less according to the amount of droop which may be becoming.
After the pattern is adjusted satisfactorily, mark with a pencil all around just inside the headsize wire. Remove the wire and cut the paper on this line. Cut pattern in two at back and lay out flat on smooth side of buckram, leaving pins in slashes. Cut close to outside edge and allow one-fourth inch for the lap at ends. Mark on buckram with pencil close to headsize line and cut one-half inch inside this mark. Lap ends one-fourth inch and backstitch closely at each edge of flap. Sew a strip of crinoline flat over seam to smooth it up. Sew headsize wire on place marked, which will be one-half inch from inside edge. Keep all joinings at back. Slash buckram from inside edge to headsize wire every half inch. Wire edge of brim and cover wire with crinoline--same method as used on sailor brim.
TO COVER A MUSHROOM-SHAPED BRIM--
If not very drooping, it may be covered without making a seam in the material. To do this, begin by placing the corner of the fabric on top at the front of the brim. Pin the front, back, and each side, always pulling with the thread of the material, and pin closely at edge, with pins at right angles to the brim. If covered with georgette, satin or silk, which is pliable, the fullness may all be worked out without a seam. Baste close to headsize wire and finish edge by following same method as used in finishing sailor brim. Also follow same method with facing. If the material used is not pliable, or if the brim is too drooping to admit of stretching the material smoothly, a seam must be made at the back. The method would be