Make Your Own Hats | Page 9

dry and more glue added. Do not sew the edge until the glue has dried. Usually it is only the material on the upper side of the brim which needs gluing down. The facing may be put on as desired. Sometimes the top of a crown has indentations, and then the velvet may be glued to stay in place.
The under or outer facing may be fitted to a rolled or close-fitting brim more easily than the upper. Beginning at the front with the corner of the material, pin at the edge and at the headsize wire. Keep the material smooth; work from right to left, and then from left to right. Work the material around to where the seam is to be made. Cut away all superfluous material, allowing three-eighths of an inch for a seam. Slipstitch together as on the top and finish the edge over wire. Whenever possible a seam should be made on the straight of the material.
A SHIRRED CROWN OF FABRIC--
There are two methods of making a shirred crown of fabric in which taffeta, satin, georgette, or velvet may be used. Velvet is especially beautiful made up in this way. The first method is the preferred. Cut a circular piece of material, having a diameter the length of the crown from front to back, measuring over the top from the headsize wire, plus four inches.
On the wrong side of the material mark circles (concentric) one-half inch apart, after first having marked a circle in the center about three inches in diameter. Gather on the line of each circle with a fine running stitch and bring the thread through to the right side as each circle is completed.
Locate the exact center of the crown top and cut a small hole at this point. Pull thread of the smallest circle up tight. This will form a bag which should be pulled down through the hole made at the center of the crown top and sewed securely in place. The material should be pinned down at four equal points at the edge of the crown, the threads of the other circles pulled up until the material fits the crown snugly. Adjust the fullness evenly and sew in place. This is an excellent way to use up old material which would otherwise show marks or any other defects.
The second method does not make as pleasing an effect, but may be used when the material happens to be in such shape that a circle cannot be cut from it. A bias strip about eight inches wide and long enough to reach around the crown, plus three or four inches, should be joined on the lengthwise thread of the material. The first shirring or gathering should be one-half inch from the edge, the additional threads should be run in evenly every half inch. The first thread near the edge should then be drawn up as tightly as possible and this edge pushed through the hole in the top of the crown. This method will require a somewhat larger opening than the first. The material is then drawn down on the outside and pinned to the bottom of the crown; the threads are then pulled tight and firm and are fastened off. Next adjust the gathers evenly and sew in place.
CHAPTER III
FRAMES OF NETEEN AND CRINOLINE
Lay the pattern on the neteen in such a way as to bring the bias where the greatest amount of roll is to be, then cut making the same allowances as if cut from buckram. This material should be used double to secure the best results. Cut one thickness first and pin this on another piece in such a way that the warp thread of one piece will lie parallel to the woof thread of the other. Cut the two pieces the same size and before removing the pins baste closely all over the brim with fine thread, making one inch stitches. Fine thread should be used for this as a coarse thread might show through the covering.
TO JOIN THE SEAM IN THE BACK--
Insert one thickness between the other two ends, and backstitch closely. This method ought to make a fairly smooth seam. Cover the seam with a strip of crinoline to smooth it up.
TO SEW EDGE WIRE ON NETEEN--
It is difficult to sew edge wire on neteen. A good result is obtained, however, by sewing the wire directly on the edge or by covering the edge first with crinoline and sewing the wire on it. Great care must be taken in handling neteen to preserve the shape, as it is very easily stretched and pulled out of shape while sewing on the edge wire. The same method is used in covering a neteen frame as with the buckram frame. The velvet, if velvet is used, can be